Issued: 4-2-2009Revised: 1-31-2013Hoshizaki “A Superior Degree of Reliability” www.hoshizaki.com Models KM-2100SWH3 KM-2100SRH3 Stackable Crescent Cu
10C. LocationCAUTION1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C
115) Install the bin control thermostat as follows: a. Remove the baffle from the bin.b. Remove the tie securing the bin control thermostat assembly.
12If a Hoshizaki B-1300, B-1500, B-1650, or non-Hoshizaki bin is used:g. Remove the 2 screws securing the thermostat bulb attachment (plastic) to the
137) Remove the thermostat bulb attachment (plastic) of the upper unit from the thermostat extension bracket (stainless).8) Carefully remove the therm
14F. Electrical Connection WARNINGFor All Models1. Electrical connection must be hard-wired and must meet national, state, and local electrical code r
15G. Installation of Remote Condenser Unit WARNING1. Installation of remote condenser unit must be performed by properly trained and EPA-certied serv
163. Setup1) Secure the legs to the remote condenser unit with the 8 bolts and nuts provided. See Fig. 10.2) The legs have 8 mounting holes. Secure th
172) Connect the refrigerant lines to the appropriate male ttings on the remote condenser unit rst and then at the icemaker. Make a proper connectio
18c. Make sure the male tting and female coupling are properly aligned, then start the connection by hand to ensure that it is not cross threaded. d.
195. Electrical Connection WARNING1. Electrical connection must meet national, state, and local electrical code requirements. Failure to meet these co
2IMPORTANTOnly qualied service technicians should attempt to install, service, or maintain this icemaker. No installation, service, or maintenance sh
20Fig. 156. Stacking Remote Condenser Units1) Install the lower remote condenser unit as described earlier in this section.2) Place the upper remote c
21H. Water Supply and Drain ConnectionsSee Fig. 16, 17, or 18 WARNING1. Water supply and drain connections must be installed in accordance with applic
221. Icemaker •Icemakerwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof1/2"ODcopper tubing is recommended for the icem
232. Water-Cooled Condensera) Connection to an Open Drain System •Condenserwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof3/
24Fig. 18 KM-2100SWH3Connection to a Closed Loop SystemBinDrainOutlet3/4"FPTCondenserWaterSupplyLineShut-OffValveCondenserWaterSupply
25I. Final Checklist WARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure tha
26J. Startup WARNING1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty cov
27III. Cleaning and Maintenance WARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any cleaning or m
281. Cleaning Procedure1)Dilute38.oz.(1,124ml)ofHoshizaki"ScaleAway"with7gal.(26l)ofwarmwater.2) Remove all ice from the
2921) Remove the front panel and fully open the cleaning valve.22)Movethecontrolswitchtothe"WASH"position.23) Replace the front pane
3IMPORTANTThis manual should be read carefully before the icemaker is installed and operated. Only qualied service technicians should install, servic
30B. MaintenanceThis icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. WARNING1. On
318) Blow the icemaker water supply line out using the compressed air or carbon dioxide supply.9) Close the icemaker water supply line drain valve.2.
32HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A2915-010
4Important Safety InformationThroughout this manual, notices appear to bring your attention to situations which could result in death, serious injury,
5See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
6See the nameplate for electrical and refrigeration specications. This nameplate is located on the rear panel.Since this nameplate is located on the
7Unit: in. [mm] B. Dimensions / Connections1. KM-2100SWH3
82. KM-2100SRH3Unit: in. [mm]
9II. Installation and Operating Instructions WARNING1. This icemaker must be installed in accordance with applicable national, state, and local regula
Kommentare zu diesen Handbüchern