Hoshizaki “A Superior Degree of Reliability” www.hoshizaki.comModels KM-1601SAH/3KM-1601SWH/3KM-1601SRH/3Stackable Crescent Cuber Hoshizaki America
10 HOSHIZAKI ICE MAKER MODEL NUMBER KM-1601SRH3SERIAL NUMBERAC SUPPLY VOLTAGE 208-230/60/3COMPRESSOR 230V 7.9RLA 65.5LRAPUMP 120V 1.2FLA 60WFAN REMOTE
11B. Dimensions/Connections1. KM-1601SAH/3 (air-cooled)Note: The storage bin opening must match the bottom opening as in the illustration.Units: mm [i
12Note: The storage bin opening must match the bottom opening as in the illustration.Units: mm [in.]2. KM-1601SWH/3 (water-cooled)
13Note: The storage bin opening must match the bottom opening as in the illustration.3. KM-1601SRH/3 (remote air-cooled)Units: mm [in.]
144. URC-21F, URC-22FUnits: mm [in.]1205[47-7/16]112 0[44-1/16]1230[48-7/16]117 8[46-3/8]444[17-1/2]75[2-15/16]380[14-15/16]659[25-15/16]68[2-11/16]39
15II. Installation and Operating Instructions WARNING1. This icemaker must be installed in accordance with applicable national, state, and local codes
16C. LocationCAUTION1. This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C
176) Install the bin control thermostat as follows: a. Remove the baffle from the storage bin.b. Remove the tie securing the bin control thermostat as
187) Replace the panels and baffle in their correct positions (unless you are installing anupper unit).Note: The bin control thermostat must be check
19Thermostat Bulb Attachment Removed from Upper UnitThermostat Extension Bracket (stainless)Thermostat Bulb Attachment of Lower UnitThermostat Capilla
2IMPORTANTOnly qualied service technicians should install, service, and maintain the icemaker. No installation, service, or maintenance should be und
20F. Electrical Connection WARNINGFor All Models1. Electrical connection must be hard-wired and must meet national, state, and local electrical code r
21Fig. 8bFig. 8aKM-1601SAHKM-1601SWHKM-1601SRHKM-1601SAH3KM-1601SWH3KM-1601SRH3•Onsinglephasemodels,thewhiteleadmustbeconnectedtotheneutr
22G. Installation of Remote Condenser Unit WARNING1. Installation of the remote condenser unit must be performed by properly trained and EPA-certied
233. Setup1) Secure the legs to the remote condenser unit with the 8 bolts and nuts provided. See Fig. 11.2) The legs have 8 mounting holes. Secure th
24d. Tighten the connection with a wrench until it is tight. At this point, the nut has covered most of the threads on the male tting. e. Mark a refe
256) Evacuate through the Schrader access ports on the Parker quick connect couplings and charge with R-404A refrigerant vapor to a pressure of 15 to
265. Refrigerant Charge (Line Set Exceeding 66 Feet)CAUTIONThe icemaker, line set, and remote condenser unit must contain the same type of refrigerant
271) Remove the louver panel. See Fig. 15.2) Remove the junction box cover on the remote condenser unit. Remove the fan motor junction box cover on th
28H. Water Supply and Drain Connections See Fig. 17, 18, and 19 WARNING1. Water supply and drain connections must be installed in accordance with a
291. Icemaker•Icemakerwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof3/8"nominalID copper water tubing or equivalent
3CONTENTSImportant Safety Information ... 4I. Specicati
302. Water-Cooled Condensera) Connection to an Open Drain System•Condenserwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof3/8
31b) Connection to a Closed Loop System•Condenserwatersupplyinletis1/2"femalepipethread(FPT).Aminimumof3/8"nominalID copper
32I. Final Checklist WARNINGCHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that
33J. Startup WARNING1. All parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty cov
34III. Cleaning and MaintenanceThis icemaker must be cleaned and maintained in accordance with the instruction manual and labels provided with the ice
351. Cleaning Procedure1)Dilute27.oz.(800ml)ofHoshizaki"ScaleAway"with5gal.(19l)ofwarmwater.2) Remove all ice from the e
3621) Remove the front panel and fully open the cleaning valve.22)Movethecontrolswitchtothe"WASH"position.23) Replace the front pane
37B. MaintenanceThis icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. WARNING1. On
385) Attach a compressed air or carbon dioxide supply to the icemaker water supply line drain valve.6)Movethecontrolswitchtothe"ICE"
39HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A1GJ10F
4Important Safety InformationThroughout this manual, notices appear to bring your attention to situations which could result in death, serious injury,
5I. SpecicationsA. Electrical Data1. KM-1601SAH (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER KM-1601SAHSERIAL NUMBERAC SUPPLY VOLTAGE 208-230/60/1 (
62. KM-1601SAH3 (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER KM-1601SAH3SERIAL NUMBERAC SUPPLY VOLTAGE 208-230/60/3COMPRESSOR 230V 9.3RLA 75LRAPUMP 1
7The rating label and nameplate provide electrical and refrigerant data. The rating label can be seen by removing the front panel. The nameplate is lo
84. KM-1601SWH3 (water-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER KM-1601SWH3SERIAL NUMBERAC SUPPLY VOLTAGE 208-230/60/3COMPRESSOR 230V 7.3RLA 65.5LRAPU
9 HOSHIZAKI ICE MAKER MODEL NUMBER KM-1601SRHSERIAL NUMBERAC SUPPLY VOLTAGE 208-230/60/1 (3 WIRE WITH NEUTRAL FOR 115V)COMPRESSOR 230V 12.8RLA 82LRAPU
Kommentare zu diesen Handbüchern