Hoshizaki“A Superior Degreeof Reliability”www.hoshizaki.comModelsC-100BAFC-100BAF-DSC-100BAF-ADC-100BAF-ADDSSelf-Contained CubeletHoshizaki America, I
10Units: mm [in.]3. C-100BAF-AD
114. C-100BAF-ADDSUnits: mm [in.]
12II. Installation Instructions WARNING• This icemaker must be installed in accordance with applicable national, state, and local codes and regulation
132. Built-In Installation SiteNOTICE• Do not let the weight of the counter rest on the icemaker.• Do not install the icemaker in a corner where the d
14C. Door1. C-100BAF, C-100BAF-ADa) Door ReversalIf you would like to reverse the door swing, follow the steps below. Otherwise, skip to section "
154) Remove hinge (B) from the right side of the unit and the 2 ller screws from the left side. Attach the 2 ller screws to the right side and attac
1612 34652. C-100BAF-DS, C-100BAF-ADDSa) Overlay Panel Fabrication and AttachmentIMPORTANTThe overlay panel must be crafted by a professional cabinet
17(2) Overlay Panel SpecicationUse the specication that applies to your icemaker (C-100BAF-DS or C-100BAF-ADDS) and the directions that follow to pr
18C-100BAF-ADDS Overlay Panel SpecicationOverlay Panel Height 27 9/16" (700 mm)Overlay Panel Width 14 13/16" (376 mm)Overlay Panel Thicknes
193) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make sure that the inserts are threaded straight and tha
2 WARNINGOnly qualied service technicians should install and service the icemaker. To obtain the name and phone number of your local Hoshizaki Certi
20ScrewsTop Panelf) Remove hinge (C1) from the top right part of the door, ip it and reattach to the bottom left. Remove hinge (C2) from the bottom r
219) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws provided. NOTICE! Ensure that the back surface of overlay p
22Snug the screws, but do not tighten.Sheet Metal BracketOverlay PanelTighten the screws.5) Fasten the overlay panel to the door using the four M4×25
237) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 26.8) Replace the door gasket in its proper orientation. Reinsert the bushin
24D. Setup1) Position the icemaker in the selected permanent location.2) Level the icemaker from side-to-side and front-to-rear by adjusting the feet.
25F. Water Supply and Drain Connections WARNINGWater supply and drain connections must be installed in accordance with applicable national, state, and
26• A water supply line shut-off valve and drain valve must be installed. A minimum of 1/4" nominal ID copper water tubing or equivalent is requi
27III. Operating InstructionsA. Important Notes About Usage WARNING• Only qualied service technicians should install and service the icemaker.• Failu
28NOTICE• Protect the oor when moving the icemaker to prevent damage to the oor.• If using the optional drain pump (HS-5061), test its operation eve
29B. Startup WARNINGAll parts are factory-adjusted. Improper adjustments may adversely affect safety, performance, component life, and warranty covera
3IMPORTANTThis manual should be read carefully before the icemaker is installed and operated. Read the warnings and guidelines contained in this bookl
30IV. MaintenanceThis icemaker must be maintained in accordance with the instruction manual and labels provided with the icemaker. Consult with your l
31A. Maintenance ScheduleThe maintenance schedule below is a guideline. More frequent maintenance may be required depending on water quality, the icem
32B. Cleaning and Sanitizing InstructionsThis icemaker must be cleaned and sanitized at least twice a year. More frequent cleaning and sanitizing may
335) Remove all ice from the storage bin.6) Remove the slope from the storage bin by carefully bending it in the center and releasing it from the 2 sl
343. Sanitizing SolutionDilute 1.25 . oz. (37 ml or 2.5 tbs) of a 5.25% sodium hypochlorite solution (chlorine bleach) with 2.5 gallons (9.5 l) of wa
3512) Open the water supply line shut-off valve.13) Plug the unit back in. Move the power switch to the "ON" position and allow the icemaker
36D. CondenserCheck the condenser once a year, and clean if required by following the steps below. More frequent cleaning may be required depending on
372) Remove all ice from the storage bin.3) Plug the icemaker back in.4) Slowly pour 24 to 30 oz. (710 to 890 ml) of water over the storage bin drain
38V. Preparing the Icemaker for Periods of Non-UseDuring extended periods of non-use, extended absences, or in sub-freezing temperatures, follow the i
39VI. DisposalThis unit contains refrigerant and must be disposed of in accordance with applicable national, state, and local codes and regulations. R
4Important Safety InformationThroughout this manual, notices appear to bring your attention to situations which could result in death, serious injury,
40HOSHIZAKI AMERICA, INC.618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A2541-010
5 WARNING, continued• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, o
6I. SpecicationsA. ConstructionTop PanelIce Discharge OpeningScoop HolderFront PanelPower SwitchLouverBin ControlThermostat BulbSlopeMagnet CatchDoor
7MOTOR-COMPRESSOR THERMALLY PROTECTED APPROVED FOR OUTDOOR USEHoshizaki America, Inc.Peachtree City, GAwww.hoshizaki.comFor certication marks, see th
8C. Dimensions/Connections1. C-100BAFUnits: mm [in.]
92. C-100BAF-DSUnits: mm [in.]
Kommentare zu diesen Handbüchern